[accident] shocking! Head Protection Supplies Defect Cases

1. Casualties caused by wearing no helmet

Case 1:

At about 11:30 noon on December 1, 2003, a lifting member Chen Moumou and Wu Moumou of a concrete component Co., Ltd. performed lifting and installing cement channels. Chen Moumou used wireless remote control to operate the vehicle, linking workers Wu Moumou responsible for the cement pipe hoisting. When the driving cement hoisting pipe is about 20 cm away from the ground, the trench pipe swings and collides with Chen Moumou's lower leg, causing Chen Moumou to fall backwards, and the head crashes into the concrete trench pipe piled up behind, and the factory truck is used immediately by employees. Sent to the County People's Hospital and rescued him to death. According to the investigation, the direct cause of the accident was Chen Moumou’s death at the time of work without wearing a safety helmet as required.

Case 2:

At 10:00 on the morning of August 7, 2009, a plumbing project team arranged for a Jiang group to replace the corrosion of a 10-ton boiler basement silo, and suggested that a helmet should be worn. At 10:20, the pipeline construction employees Jiang, Qu, Zhang, and Niu arrived at the job site and found that the replacement of the steel pipe must be carried out by overhead welding, and the helmet cannot be worn. Jiang discovered that there was an I-beam that could easily hit the head. Ministry, and to remind cattle attention. At 10:35, the welder Niu certain welding operation was finished. When checking other welding sites, due to the narrow space, Niu accidentally hit the I-beam on the head, causing severe skin bruise on the head.

Case 3:

On June 11, 2007, Zeng Moumou, a coal miner in Hunan Province, entered the hole and was about to repair the machine. At the time, he put the helmet in his hand and did not wear it on his head. When he was walking to the +116 level along the coal When the work face was dug, the top suddenly fell and it fell. Zeng Moumou was hit by a falling stone and lost his consciousness on the spot. The on-duty personnel immediately organized a rescue and sent Zeng Mouxing to the hospital for emergency treatment. However, due to his injuries, he died after being rescued.

Case 4:

On May 30, 2005, at a blasting quarry in Liuyang City, Hunan Province, a gravel worker did not wear a helmet and was hit by a splash of gravel. He died on the spot.

Case 5:

On March 4, 2008, four maintenance staff of a steel structure company in Shandong Province stood directly on the roof of the workshop without maintenance of the safety net and the channel board during the maintenance work. The seat belt was not fixed on the reliable object. . Three of the employees wore helmets, while the other employee did not wear a helmet. When the employee who did not wear a helmet replaced the lighting tile and used an electric drill to withdraw the nail, he accidently stepped on the non-load-bearing skylight, and the seat belt was not fixed. , Falling from a height to the ground, died after being rescued on site.

2. Wearing a bad quality helmet causes casualties

Case 1:

On April 7, 2007, at the construction site of Hangzhou Paradise Construction Co., Ltd. in Xiaoshan District, Hangzhou City, Zhejiang Province, He Moumou, a staff member for reinforcing steel straps, and 40 other employees together began work on the construction site. Due to the delivery of a batch of rebars from the site the previous day, they were transported to the roof of the 5th floor. He Moumou used the steel wire to tie up 6 steel bars on the ground floor and hang it on the roof. Two of the bundled steel bars suddenly slipped down from a height of 18 meters when they were hoisted to the roof. Despite wearing a safety helmet, one of the bars was inserted directly into the brain of He X with a safety helmet and the other was inserted into the soil less than 5 cm away from his body.

According to other employees, the hard hat he wore was only sold for 3.5 yuan. The quality is very poor. If it is a good quality helmet, the consequences of being put on the brain may not appear.

Case 2:

At 7:40 am on January 26th, 2015, when a production employee at a construction site in Lianyungang City, Jiangsu Province, was finishing materials, a steel bar about 50 centimeters long and about 1 centimeter in diameter suddenly fell from the sky and pierced his head. The safety helmet was inserted into the skull of the worker and was sent to the Lianyungang City Hospital for rescue.

3. Fatal accident caused by improper wearing of safety helmet

Case 1:

On the construction site of a building, a production employee wearing a helmet without a chin strap is responsible for tying bamboo poles and suspending them on a hook under a crane. When the bamboo poles are lifted, suddenly a bamboo basket falls down. Exactly the middle of his safety hat and cap, knocking the helmet over the ground, when the employee instinctively receded, he accidentally fell, the back of the brain hit the ground, died after being rescued by the hospital.

Case 2:

At 8 o'clock on May 23, 2005, at the construction site of a residential building in Jilin City, Jilin Province, a construction employee accidentally fell from a height of 1.5 when he dismantled the structural column, because the helmet was thrown off without the lower jaw. The head hit the column and was sent to the hospital to die.

4. Without a protective cap, the scalp is rolled up and caused casualties

Case 1:

On a certain day on a certain day in the month of 2006, Li, a female mechanic at a machinery factory in Ziyang City, Sichuan Province, came to the workshop and handed over the first day's finished work pieces to the next production process employee Renmou. Since there were no parts to be processed in the hand, Not wearing any protective equipment. Because Renmou entered the factory for a long time, the technology is good, Lee would like to take the apprentice together to learn technology from him, so he called the apprentice Pengmou to see Renmou operation together. When Lee recruited apprentices to watch any of the operations, he was accidentally tripped over by the lathe's foot pedal. His hair was twisted on the rotating bar of the lathe, and the scalp was torn open. After 10 minutes, 120 came and rescued Lee from the lathe and sent it to the hospital. After rescue, Lee was out of danger but the sutured scalp did not survive and his hair could not be regenerated.

Case 2:

On the afternoon of June 8, 2006, Shen Moumou, an employee of a company in Taizhou City, Zhejiang Province, was involved in the use of the color testing machine. Because of the illegal operation, he did not wear a protective cap, causing the hair to become involved in the drive shaft during the operation, causing him to be Extruded.

Case 3:

On March 5th, 2014, a certain type of 2535 vertical drill tapping (drilling speed of 60 rpm) was used by a lithemaker of an anchorage factory in Zhejiang Province, and the protective cap fell off to the ground without closing the equipment. Li Moumou bowed his head and raised his head to throw the hair on the drill pipe. The drill pipe twisted the hair. The worker at the workshop discovered that the power of the device was immediately turned off. He rescued Li Moumou from the drill press and reported it to the hospital. Treatment, diagnosed as partial scalp shedding.