 I engaged in feed particle machine, farm machinery and farmers and feedlots special equipment. City Bureau of Animal Husbandry is designated to promote the excellent mechanical, but also the majority of farmers receive substantial economic benefits the most dependent, the best equipment money. Below Introduce the use and maintenance of the feed pellet machine :
　　 1. Before using the machine , the machine should be thoroughly cleaned and inspected , the belt tension should be adjusted , and then the power supply should be connected , and the direction should be rotated .
　　 2. Adjust the " pressing screw " of the pressure roller to 0.1-0.3 mm between the pressure roller and the template .
　　 3, when taking the test machine 15 kg powder (calculated according to type 200C, 5 kg and less small, large multi 5 kg), preferably with rice polishings, 5 pounds of meat or peanut Jiamai Pi 15 kg pressure test, repeated rolling after pressing for 15 minutes, not the pressure, the feed hole template with a vise clamp nails (not with a pointed nail, the nail heads preferably polished) open, and then compressed until the normal discharge. If the user's own formula feed can't be pressed out , then the feed material of the mold hole is opened , the food oil is put on the flat mold surface , and then the above-mentioned rice husk or peanut meat and wheat husk feed are pressed out, and then the fine sand is added. (building sand) repeatedly pressing for 10 minutes until the normal discharge.
　　 4 , the length of the pellet feed can adjust the upper and lower position of the cutting knife .
　　 5, the template can be removed if replacement cartridge filled hopper is removed, remove the pressure wheel and cutter, gongs twist off the cap on the spindle, with attachment "chest" hanging out flat die, (templates can be used double-sided, generally After processing 50,000 jin, use it to turn over, and use 105A type 25,000 jin to turn over ).
　　 6, for safety, when the cover is removed, must be off the power switch to turn off the machine, hand and other tools to the contact pressure wheel template.
　　 7. When the machine is rolled to 20,000 kg of decompression wheel for cleaning and maintenance of copper lubricant , a comprehensive maintenance and refueling is carried out every six months .
　　 8 , 105A single-phase motor , please ensure 220V voltage .
　　 9. Install the grounding device with the pole of the motor .
　　 10. For models that use electric motors , customers must install overload protection devices .
In the company: rather bear the loss, do not want to lose credibility, adhere to the "full service, the reputation of Germany a hundred years," the service concept, the present and look to the future, willing to work with customers and friends at home and abroad go hand in hand, create a better future.
---
**Feed Pellet Machine: Usage and Maintenance Guide**
As a professional manufacturer of agricultural equipment, we specialize in feed particle machines, farm machinery, and specialized equipment for livestock farms. The City Bureau of Animal Husbandry recommends our advanced mechanical solutions, which have brought significant economic benefits to farmers. Our high-quality equipment is designed to deliver maximum efficiency and durability.
Here’s a detailed guide on how to use and maintain your feed pellet machine:
1. **Preparation Before Use**:
Ensure the machine is clean and thoroughly inspected. Adjust the belt tension, connect the power supply, and check the rotation direction before starting.
2. **Adjust the Pressing Screw**:
Set the gap between the pressure roller and the template to 0.1–0.3 mm. This ensures optimal compression and pellet quality.
3. **Test Run**:
Start with 15 kg of powder (adjust based on the model—e.g., 5 kg for small models, up to 15 kg for larger ones). Use materials like rice husks, meat scraps, or peanut meal for testing. If the pellets don’t come out, open the mold holes and apply some oil to the die surface. Then press again using the same materials and gradually add fine sand to help the process.
4. **Adjust Pellet Length**:
You can control the length of the pellets by adjusting the position of the cutting knife.
5. **Replace the Die**:
When replacing the die, remove the hopper, pressure roller, and cutter. Loosen the spindle cap and use the provided "chest" tool to remove the flat die. Dies can often be used on both sides. Replace after about 50,000 kg of production for most models, or 25,000 kg for the 105A type.
6. **Safety Precautions**:
Always disconnect the power supply before removing the cover. Avoid touching the pressure roller and die with your hands or tools during maintenance.
7. **Regular Maintenance**:
After processing 20,000 kg, clean and lubricate the copper parts. Perform a full maintenance and refueling every six months to ensure smooth operation.
8. **Voltage Requirements**:
For 105A single-phase motors, make sure the voltage is stable at 220V.
9. **Grounding Installation**:
Install a proper grounding device on the motor to prevent electrical hazards.
10. **Overload Protection**:
For all motor-driven models, ensure that overload protection devices are installed to safeguard against damage.
At our company, we prioritize customer satisfaction and long-term trust. We believe in the philosophy of "full service, lasting reputation," and we are committed to working with clients worldwide to build a brighter future together. Whether you're looking for reliable equipment or expert support, we're here to help.The classic design of the Peristaltic Pump head has strong chemical resistance, stable performance, wide flow range, stronger practicability, convenient operation and wide application.
Our main products include micro pumps, pump control systems, micro peristaltic pumps, micro diaphragm pumps, vacuum pumps and accessories. All products can be customized according to your special requirements. Our products are widely used in medical machinery, Laboratory equipment, water treatment, printing, automotive products, etc.
Multi-channel peristaltic pump head,Micro peristaltic pump head,Mini peristaltic pump head
Changzhou Yuanwang Fluid Technology Co., Ltd. , https://www.ywfluid.com