Labeling machine maintenance precautions

Labeling machine mainly includes: paste labeling machine, self-adhesive labeling machine, sleeve labeling machine, round bottle labeling machine, beer labeling machine, semi-automatic labeling machine, labeling machine, automatic labeling machine, automatic Labeling machine, labeling machine, automatic labeling machine, hot melt adhesive labeling machine. These products can be flat-paneled, single-sided or multi-faceted packaging, cylindrical paste, partial or full-covering cylinder paste, dents and corners, etc. If you want the labeler to last longer, then we To take good care of the labeling machine, you must first pay attention to its maintenance.

1. Adjustment of the brushing device: the center of the brush is aligned and the two sides are symmetrical. The brush is perpendicular to the surface of the container. The overlapping gap of the brushing sweeping container is: a single pressing brush is 10 mm to 15 mm, and the combined pressing brush is 5 mm to 10 mm. The position of the cleaning brush from the sponge is 1 mm to 2 mm. Adjustment of the bottle head. The bottle head should be 20mm lower than the bottle when there is no bottle.

2. Adjustment of the label box: the center line of the label box, the central axis of the label station is tangent to the label paper, and the center axis of the label board is lined up at three points. The adjustment target board is tangent to the label paper (0 distance), and then the label box is moved closer. 1mm ~ 2mm can be. The gap between the standard paper and the bead on both sides should be between 0.8mm-1mm. The gap is too large, causing the standard paper to shift in the standard box, and the skew mark appears. If the gap is too small, the push mark will be poor. The adjustment of the position of the labeling hook of the standard box: the upper and lower and the left and right grasping hooks are on the same vertical plane and evenly work on the standard paper, so that the label can be smoothly captured. Adjustment of the label supply roller: When there is no label, the label holder can be pressed to the foremost end of the cassette and when the label is attached, the label near the label hook cannot be crushed.

3, the adjustment of the bottle star wheel, the bottle star wheel, the bottle screw: When adjusting the inlet and outlet star wheel and the bottle screw, the pressure bottle head of the standard machine shall prevail. First adjust the bottle into the star wheel. When the bottle head just overwhelm the bottle, adjust the bottle into the star wheel so that the bottle is in the middle of the star wheel groove. Adjustment of the inlet screw: According to the inlet star wheel, when the bottle is in the middle of the groove of the inlet star wheel, adjust the auger so that the auger is pressed against the bottle side without displacement. Adjustment of the bottle star wheel: When the bottle head has just been lifted, adjust the star wheel so that the bottle is in the middle of the groove of the star wheel.

4, the adjustment of the squeegee and the rubber roller: the squeegee and the rubber roller can not have a gap in the whole length. If there is a gap, the squeegee can be adjusted by adjusting the eccentric bolt. Adjustment of the rubber roller and the target plate: the target plate and the rubber roller only contact each other without any pressure. If the gap is too large, the glue on the label will be too much, causing the glue. The gap is too small, the contact is too tight, the glue will be squeezed away, and there is no glue on the half of the target. Practice has proved that the gap between the target plate and the rubber roller is between 0.1mm and 0.2mm. This can be achieved by adjusting the bearing housing in the lower part of the rubber roller and adjusting the bearing on the upper part of the rubber roller if necessary.

Global hardware network

Concerned about surprises

Label: Maintenance notes for the labeling machine

Previous: Maintenance method of ball mill during running-in Next: Use and maintenance of edible oil filling machine

DH Chinese version CCTV IP Camera

CCTV Ip Camera,Hd CCTV Cameras,Mini CCTV Ip Camera,CCTV Ip Camera System

TD Cloud Security Co.Ltd , https://www.cctvcameraexpert.com

This entry was posted in on